Proformer C6-12116 - 10' 1" X 16 Gauge Claw-Style Box & Pan Brake

Features:  

• Section fingers are precision machined from rolled steel bar stock for maximum strength. 
• The fingers can be adjusted or removed quickly by the loosening of the thumb screw. 
• Heavy duty steel plates and tension bars are incorporated for maximum accuracy.
• Allows forming 6" depth boxes 
• Available in 4', 5', 6', 8' and 10'  - 16, 14 or 12 Gauge
• Stock finger widths are 2", 3" & 4".  OR, you may specify any width and assortment.  Ask about additional fingers or full sets.
• Bolt-On Radius Bars are available including 1/16" through 1/2" radius or radius can be added to the leading edge of the fingers in a wide range of radii.
• Minimum Reverse Bend: 1/2" at reduced gauge with apron angle removed.  A 1/4" return apron is optional.
• Beam Set Back Adjustment is 1".  Additional set back is optional and will be needed for bolt-on radius bars greater than 1" diameter (1/2" Radius)
• Lift of Beam is 2-1/4" at leading edge of fingers (EXCEPT 2 MODELS: 4' X 16 Gauge and 4' X 14 Gauge is 1-1/2")
• Six (6) adjustable truss rods for center alignment 
  

Options:  

• Hydraulic Assist for L, U & C Models - The way to form 8' or 10' of 16 gauge or any length heavier gauge up to 10' of 12 gauge mild steel.  $3,500.00 Includes foot switch that can be used from either end of the brake (or deduct $100.00 for frame mounted switch).  You can adjust the speed so that you will achieve a 90° bend in about 8-15 seconds.
• Down Flange - Now you can form down flange shapes including transverse duct by creating openings in apron fingers and table blocks.  Add to the price of any model: 3' & 4' $1,500.00, 5' & 6' $1,900.00, 8' $2,400.00 and 10' $2,700.00.
• Rear Operated Manual Back Gauge - Usable depth of 48", you can bend sheet metal at the same depth time and time again.  Call if you need a depth of more than 48".  Add to price of any model: 3' & 4' $350.00, 5' & 6' $410.00, 8' & 10' $480.00
• Bolt-On Radius Bar 1/16" to 1/2" Radius - 3' &4' $95.00, 5' & 6' $137.00, 8' & 10' $231.00.  Many more radius sizes are available - Call for Quote.  NOTE: Using a Bolt-On Radius Bar requires a Bolt-On Apron Angle if the radius is greater than 1/4" (1/2" Diameter).  See Bolt-On Apron Angle below for availability.  *Bolt-On Radius Bars might not work above 20 gauge mild steel or .050" aluminum.
• Magnetic Radius Bar - Can be used at full rated capacity of the brake and hold themselves on without bolting.  They are also suitable for cutting up into segments for use with finger brakes.  3' $315.00, 4' $368.00, 5' $424.00, 6' $473.00. 8' $578.00 and 10' $683.00
• Radius Fingers - Added to the leading edge of clamp or fingers: 3' & 4' $90.00, 5' & 6' $180.00, 8' & 10' $270.00
• 1/4" Minimum Reverse Bend Apron - If desired, may be ordered and will cost no more on L & U 8' & 10' X 16 Gauge Models.  It is an extra cost on all others: up to 4' $150.00, 5' & 6' $185.00, 8' $245.00, 10' $300.00.  This modification includes machining of the apron to allow 1/4" minimum reverse bends, and a bolt-on insert to build the apron back out to 1/2".  NOTES: The rated capacity of all brakes assumes using all provided inserts and apron angles.  When a brake is used without bolt-on insert, capacity is reduced to 24 gauge.
• Bolt-On Apron Angle - Included on all models except 3' to 6' X 20 Gauge.  For $11.00 per foot you can add a bolt-on apron angle to your 3' to 6' X 20 Gauge Brake.  It will increase the full-length capacity to 18 gauge.  This option will be needed if using a bolt-on radius bar larger than 1/2" diameter on 3' to 6' X 20 gauge models.  All other models already include a bolt-on apron angle.
• Counter Weights - Included on all 16 Gauge, 14 Gauge & 12 Gauge Models and Optional an all others: for 3' &4' X 20 Gauge or 18 Gauge Brakes and 6' X 22 Gauge $50.00 Each, 5' & 6' X 20 Gauge or 18 Gauge $80.00 Each, for 14 Gauge and heavier, Please Call.
• Leg Kit for 3' or 4' X 16 Gauge and Lighter Brakes - (All other models are built-on legs) 55 lbs. $86.00*  EXCEPT: 4' L & U X 16 Gauge Models are available as floor models with welded on legs that weigh 110 lbs. $110.00.
• Special 4" Cut Back Finger - Bends 3/16" mild steel up to 4" wide without adjusting set back or clamp pressure is included with U models and is optional for 16 Gauge BP models.  Up to 14 Gauge $35.00, for 12 Gauge $45.00.
• Complete Set of Fingers U & BP Models 20 & 16 Gauge: 3' $168.00, 4' $180.00, 5' $225.00, 6' $270.00, 8' $366.00 and 10' $455.00
• Complete Set of Fingers U & BP Models 14 & 12 Gauge: 3' $218.00, 4' $234.00, 5' $292.00, 6' $350.00, 8' $478.00 and 10' $593.00
• Additional Stock Fingers - 2", 3" or 4" for U & BP models: 20 gauge to 16 gauge $26.00 Each  14 gauge to 12 gauge $38.00 Each
• Full Length Finger U & BP Models - 20 & 16 Gauge 3' or 4' $155.00, 5' or 6' $182.00, 8' $305.00 and 10' $367.00.  14 & 12 Gauge add 30%
• Additional Fingers for C6 models - Any combination: up to 36" $1,125.00, 4' $1,353.00, 6' $2,046.00, 10' $2,393.00.  A full-length one piece finger for C6 models: up to 36" $905.00, 4' $1,089.00, 6' $1,450.00, 8' $1,650.00, 10' $1,930.00